Sawdust Journey Logo
SawdustJourney
Woodworking

Riser Block vs. 17-Inch Bandsaw: The Real Cost of Resawing

Marcus Washington
November 17, 2026
Bandsaw blade coiled around a metal riser block on a dusty workbench beside a wood plank

Riser Block vs. 17-Inch Bandsaw: The Real Cost of Resawing - A step into the workshop.

NEW FREE TOOL

Stop Wasting Wood

Generate clear cut diagrams instantly with our new Cutlist Optimizer. Plan your cuts to make your next build easier.

Yo, let me tell you a story. A guy on my block puts a slab of white oak out on the stoop — six quarter, rough, still got the bark line on one edge. It sits there two days. I walk past it four times before I knock. He says take it, it's from a tree that came down in the storm. Now it's in my second bedroom, leaning against the wall my landlord thinks is for guests, and I've got a choice to make. Resaw it, or buy thin and eat the price.

That's the whole question, and New York makes it sharper. I don't have a truck. I don't have dust collection worth the name. My shop is thin walls and a window. Every board foot I bring up the stairs is a board foot I paid for and hauled. Waste hurts more here.

First, the three doors and what they cost

Grizzly's own pages give you the clean comparison. The 14" G0555 is $820 (list $895), 1 HP, 6" of resaw height, 93-1/2" blades up to 3/4" wide. The riser kit, H3051, is $159.95 and takes that 6" to 12". Add it up: $979.95 for twelve inches of height on one horsepower.

The 17" G0513Z is $1,575 (list $1,750). That's $595.05 more than the 14-plus-riser, and it gives you 12-1/8" of height, 16-1/8" of throat, and a frame that takes a 1" blade with no splice in it. Grizzly also sells 14"-class resaw saws at $1,525 and $1,895 — at or above the 17" price. Sit with that for a second.

The third door is the mill. Wood-Mizer's 2026 pricing guide, which is a sawyer's guide to what operators charge, puts custom sawmilling at $0.35–$0.75 a board foot for standard work and $0.75–$1.00 for hardwoods or custom cuts, with $100–$200 minimum job charges. Here's the catch, and I want it in bold in your head: those numbers price sawing logs into lumber. Resawing your dry, squared board is a different job. Nobody published a clean customer-facing resaw rate I could verify. Vintage Timberworks describes the service — splits 2" reclaimed stock into two 3/4" pieces with one old face, minimum thickness about 3/8" — but publishes no price, and wants a 100 board foot minimum to custom-mill.

So the mill door is real, but you're driving to it with a minimum order and a board you already own.

The riser block is where the math gets cute

Here's the false economy, and it's not about the $159.95. Sawblade University says it plainly: a riser spacer affects how rigid the saw feels under load, and that can show up as more vibration, lower peak blade tension on some models, and tracking drift if the block isn't perfectly square and level. It lists as a poor fit "saws with motors under 1 HP that already struggle to hold tension on wide blades," and says a riser will not fix an undersized motor, a worn frame, or a saw that can't hold tension.

Read that again. One horsepower. That's the G0555.

Popular Woodworking's Vondriska did his resaw tests on an inexpensive 14" saw with a 3/4-hp motor and a riser, and still warns that pushing a saw too hard can bog it down or pop a breaker. Over on the Fine Woodworking forum, the thread from January 2022 is a pile-on. A Jet owner with a riser says "the power just isn't there" and ended up cutting both sides on the table saw first. One reply: "Most 14" cast iron bandsaws with riser block are low on power and poor on blade tension... these saws do struggle." Another: "anything less than 2hp will not resaw proficiently and 3 hp is better... the makers of those 14" Delta clones don't tell you that when they sell you the riser blocks."

It's contested, and I'll give you the other side. One poster resaws 10" cherry "like butter" on 1.75 HP. One guy with a 1 HP Jet and a riser did 9"-wide cherry with a 1/2" Wood Slicer and had no issues. Another got a Rigid to "a decent saw for resawing up to 8 inch wood at a slow pace" after a 1.5 HP motor, riser, bearing guides, a Wood Slicer, and "a lot of tuning." That last phrase is doing a lot of work.

Now price the whole path. Popular Woodworking's 2019 figures: riser about $110, bearing guides about $150, motor about $200. That's $460 before blades, at seven-year-old prices. Today's riser alone is $159.95. Compare $460-ish to the $595.05 gap between the two Grizzly saws and draw your own line. I'm not going to tell you the upgrade saves money, because the sources don't say that. I'll tell you what I see: you're spending most of the difference to end up with a spliced frame, one horsepower, and a saw you had to tune.

Also, the trap. Riser blocks fit the two-piece cast-iron 14" frame — Sawblade University lists Delta 28-203, Jet JWBS-14CS, Grizzly G0555, Rikon 10-324. Welded or steel-frame saws have no split point. Blade length jumps from 93-1/2" to about 105". The Grizzly kit ships with a 3/8" x 105" x 6 TPI blade, and a 105" x 3/4" x .025" x 3 TPI thin-kerf blade, H8567, runs $47.95.

Blades, kerf, and the loss you can't measure

Blade specs are where the sources argue. Olson Saw says 1/2" to 3/4" wide, 0.025" to 0.032" thick, skip or hook tooth, 2–3 TPI, and calls thin kerf preferable for maximizing yield in expensive woods. Vondriska says look for four teeth per inch and a hook pattern. Sawblade University says 3 TPI for 10–12" resawing. Common ground: low TPI, hook or skip, wide blade, thin kerf when the wood is dear.

What I can't give you is a kerf-loss percentage. Olson confirms thin kerf maximizes yield but doesn't publish a kerf width. Blade thickness is not kerf — set teeth cut wider. So I'm not going to hand you a number that looks authoritative and isn't. Kerf loss is real, and it compounds over every board you resaw. Judge it by feel and by your own scrap pile, not by a figure I made up.

Drift, though, is a setup step, not a defect, and that's from Popular Woodworking. Draw a line on a 16" scrap, saw it freehand, note the angle you had to feed at, stop halfway, trace the angle onto the table, set the fence parallel to that line, test-cut, adjust. It varies blade to blade, so redo it every change. Board pulling away from the fence on the outfeed means the fence is angled too far from the blade. Binding means too close. And check tension with the saw unplugged, upper guide raised: push the side of the blade, it shouldn't deflect more than 1/4".

The species math that actually decides it

Here's where the arithmetic gets honest. The Woody Yard's November 2026 list: Walnut $16.50/bf at 4/4 and $17.00 at 8/4. White Oak $10.00 at 4/4 and $15.00 at 8/4. Cherry $6.75 and $8.70. Hard Maple $8.35 and $9.20. Volume discounts run $0.35/bf at 20+, $0.70 at 50+, $1.05 at 100+ on domestic lumber.

Look at that spread. Walnut asks fifty cents more per board foot for 8/4. White Oak asks five dollars. Poplar asks thirty-five cents. Hickory asks $3.75.

Now the honest part: that spread is the raw premium for thicker stock, and it is not savings. 8/4 yields two boards plus a kerf and dressing loss. You don't get a free extra board. If the spread is small — walnut, poplar — buying thicker is close to a wash and you skip the whole machine question. If the spread is wide — white oak, hickory, cherry — resawing starts to look like a job worth doing, provided your saw can do it without burning a blade and a Saturday.

Woodcraft gives you the sequencing that protects the yield. Resaw before planing: "if you have any resawing on your agenda, now's the time to do it." Joint one face flat, resaw, then plane to thickness. Lay out parts at least 1/4" oversize in width. Let rough-sized pieces relax a few days to a week before final milling, because cutting releases stress and the wood moves again. Popular Woodworking says the same thing from the other end: wood can be imperfectly dried and react after it's cut, so cut thick enough to plane out the cup. That's the loss nobody quotes — not kerf, not drift, but the thickness you left yourself so the board didn't cup into a shim.

Veneer: the reason some of us bother

Slicing veneer is where a bandsaw earns its keep in a small shop. Popular Woodworking sets shop-sawn veneer at 3/32", thick enough to work, thin enough to be stable, edge-glueable with light clamp pressure. Vondriska's line is the one that sells it: slicing veneer can change one board foot of precious, expensive wood into six square feet of veneer. Resaw down to 1/2" remaining is about as far as you can safely go on the sequence.

Two practical catches. Planer tables often rise no closer than 1/8" to the cutterhead, so surfacing the band-sawn face needs a backer board. And cut veneer from dry stock, from the side away from the fence, re-jointing the face between cuts.

So what do I do with the oak on the stoop

If you're resawing walnut and poplar at fifty cents and thirty-five cents a board foot of spread, buy thicker and save your Saturday.

And that's the judgment I'll actually make. A riser block on a one-horse 14" saw is a way to spend $979.95 and most of the way to a 17" price on a spliced frame. The $595.05 gap buys you a real motor, a real throat, and a 1" blade capacity. If the wood in your shop is worth resawing, that gap is the cheapest money in this whole article. Before you spend it, though, call the yard and ask what they charge to resaw your board. Get a number. If it's under the spread times your board feet, pay the man and keep your weekend.