CPSC Table Saw Rule Withdrawn: What It Means for SawStop Prices

CPSC Table Saw Rule Withdrawn: What It Means for SawStop Prices - A step into the workshop.
Stop Wasting Wood
Generate clear cut diagrams instantly with our new Cutlist Optimizer. Plan your cuts to make your next build easier.
We've all been there. You're standing in the shop, the saw is unplugged, and you're staring at a project budget that has to cover a birthday gift, a wedding present, and whatever the kids need for school this month. Somewhere in the back of your mind is the noise from last year: the federal government was going to force every table saw to stop on contact with skin. Maybe you thought you'd wait it out. Maybe you thought the prices would shift.
On August 20, 2025, the Consumer Product Safety Commission announced it was withdrawing several rulemakings, and the list explicitly included the Safety Standard Addressing Blade-Contact Injuries on Table Saws. That's the rulemaking that began with a petition from Stephen Gass, David Fanning, and James Fulmer back in April 2003, the one that sat through an advance notice in 2011, a notice of proposed rulemaking in 2017, and a supplemental notice in 2023. The CPSC said it "does not intend to issue final rules" on the table saw standard. Acting Chairman Peter A. Feldman signed a statement the same day.
So the regulatory clock is gone. What does that actually mean for your shop?
What the rule would have required, and what it didn't
It's worth being precise, because the online chatter has not been. The proposed rule was a performance standard, not a technology mandate. According to the CPSC's Supplemental Notice of Proposed Rulemaking published at 88 FR 74909, table saws would have had to limit the depth of cut to no more than 3.5 millimeters when a test probe, standing in for a finger, approached the spinning blade at 1 meter per second.
In other words, the rule described an outcome. It did not name SawStop, and it did not require any specific brand's cartridge system. Any manufacturer that could meet the performance number was free to do so however it liked. That distinction matters because the licensing fight was always about patents, not physics. SawStop describes its own system as stopping a spinning blade on contact with skin, with the blade stopping in less than 5 milliseconds and dropping below the table.
Safety science support for the proposal was real. UL Solutions, as quoted by ToolGuyd, said it "strongly support[s] this proposal" and that active injury mitigation technology "will significantly reduce the incidents of devastating and life-long injuries caused by table saws." The same quotation notes that riving knives and blade guards "have not changed the rate of injury or injury severity." That's not nothing.
But the record was contested. CPSC's own 15-year trend analysis, cited in the 2023 SNPR, found no reduction in table saw injuries from 2010 to 2018, despite a voluntary standard that became effective in 2010 requiring modular blade guard systems. You can read that two ways, and the agency's commissioners did. The 2023 SNPR estimated the rule would prevent or mitigate 49,176 medically treated injuries per year, with net benefits of $1.28 billion to $2.32 billion annually. Those are the agency's estimates, and they were argued about in the docket.
Feldman's own framing was blunt. In the CPSC release 25-440, he said regulations that "promote unscientific agendas, impose unnecessary costs, and reduce competition are no longer agency priorities." He also accused SawStop of "rent-seeking behavior," and after a 2024 lawsuit said the record raises "serious concerns about SawStop's monopolistic intentions and its exploitation of CPSC's rulemaking process," as quoted by ToolGuyd. SawStop, for its part, has declined to license its technology, according to ToolGuyd's characterization.
I'm not going to referee that fight here. What I care about is what it means for the person deciding between a used contractor saw and a new SawStop.
The price ladder is exactly where it was
Here's the part that surprised me. The withdrawal changed almost nothing about SawStop's own pricing. Its build-and-price page lists the Compact Table Saw CTS at $899, the Jobsite Saw Pro JSS at $1,699, the Contractor Saw CNS at $1,999, the Professional Cabinet Saw PCS at $3,025, and the Industrial Cabinet Saw ICS at $5,154. Those are starting prices, as listed. Nothing in the August 2025 action moved any of those numbers.
You may see the PCS quoted at $3,355 with a 36-inch T-Glide fence, and that's not a contradiction. It's a configuration difference. Fence and rail choice moves the number. The same page also showed a promotional banner advertising $350 off a Professional Cabinet Saw through January 3, 2027, which tells you the manufacturer is working the sales calendar rather than the regulatory one.
The floor didn't move either. SawStop's cheapest saw starts at $899. If you were hoping the rule would somehow pull active injury mitigation down to a $300 benchtop budget, the withdrawal didn't cause that gap, and it didn't close it. The gap is structural. It's the cost of the hardware.
And if you do buy in, budget for the trigger. SawStop lists the standard 10-inch brake cartridge at $119. A blade is also consumed in a trigger event, because the saw stops by driving the cartridge into the blade. I can't give you an honest blade-dollar figure per event, so treat that as the unknown you'll absorb. The zero-clearance inserts run $75 each, and if you're a dust-collection person, the overarm setup is $349 and the blade guard is $169.
That's the real ownership picture. It's not a subscription, but it isn't zero either.
The used market: what I can and can't tell you
This is where I have to be honest with you, and where a lot of articles on this topic are going to let you down. I don't have verified used-saw pricing to give you. No resale percentages, no "the used market is softening" claim. If someone tells you the withdrawal sent used prices in a particular direction, ask them what dataset they used, because I couldn't get one.
What I can tell you is how I'd approach that decision in my own shop. If you're weighing a used contractor saw against a SawStop PCS, the gap is several hundred to several thousand dollars. The withdrawal didn't change the physics of a spinning blade, and it didn't change the price of the machine with the brake on it. What changed is that you're no longer waiting for a rule that might have leveled the field. If you were waiting, the wait is over and the field is not level.
A used saw with a riving knife and a blade guard is still a legitimate tool. That's what most of us learned on. The voluntary standard did put modular guards on new saws from 2010 forward, and the injury trend analysis suggests that didn't move the needle much, which is precisely the argument the rule's supporters used. Draw your own conclusion from that. I know what I'd tell a friend who asked.
The "wait for blade-contact technology" question
This is the question I hear most, usually from someone who is otherwise ready to buy. And the honest answer is that the specific thing people were waiting for is gone. The CPSC stated it does not intend to issue final rules. There is no regulatory deadline to wait out.
What about the patent clock? I can't give you years or numbers, because I couldn't verify them from a primary source and I'm not going to print a number that somebody pulled out of a forum thread. What the CPSC docket does note, in 88 FR 74909, is that the expiration of two SawStop AIM-related patents occurred as a market change before the 2023 supplemental notice. That's the only patent-expiry fact I have. It also notes a Preventative Contact System on a commercial sliding table panel saw, which tells you non-SawStop contact-sensing technology exists, but on industrial equipment. There is no verified consumer-market price for competing active mitigation, so I'm not going to pretend to give you one.
And one more caution. The withdrawal is a policy shift, not a statutory bar. Nobody I read states it's irrevocable. ToolGuyd framed it accurately as "no decision on table saw safety," which is different from a decision against safety. I wouldn't plan my shop budget around that, but I also wouldn't pretend the question is permanently settled.
What I'd actually do
If your budget allows a SawStop and the brake is the reason you'd sleep better at night, the withdrawal didn't make that purchase any worse or better. Buy the machine you want for the reason you want it. The $119 cartridge is a real line item, and you should know that going in.
If your budget doesn't allow it, buy a used saw with a riving knife and a guard, learn to use a push stick the way your grandfather did, and put the difference into lumber and a good blade. The withdrawal didn't make that saw less safe. It just made the decision clearer, because you can no longer tell yourself you're waiting for a rule.
And if you were holding off on a gift project because you weren't sure what the saw situation would look like by the time you finished it, pick a project this weekend. A maple coaster set or a small cherry keepsake box doesn't care what the CPSC did in August. The shop clock is the one that matters.